I am no longer under warranty and am pissed because I just had to replace my driver's Xenon headlight housing that mysteriously stopped working about 1000 miles after warranty expiration. If I was going to the trouble, I think I'd rather have new parts installed (with a warranty). The photos were an excellent resource. It requires a long T-handled Allen wrench to do the job. have a peek at this web-site
Without this article, we would have let our customer down by informing him we could not repair the window. If you would like login information re-sent to you, click on the button below to request your login information to be re-sent. They can figure out what part or repair kit you need. - Nick at Pelican Parts ilio Comments: Your instructions and photos are great! Thanks dude!!!
What doesn't help is the fact that my driver's side interior door release is inoperable, so I HAVE to roll down the window to get out. Glad to know we are not alone ! NOTE: This is not an official Mini U.S.A. February 25, 2015 Followup from the Pelican Staff: Thanks for the feedback.
At first it was that the door didn't close properly because the window didn't dip. Then remove one fastener at the side, then finally the fastener that is accessed through a hole below the speaker. Carefully remove these clips with a pry tool. Mini One Window Not Working Now, look at the sides of the door panel.
The window regulator is inside the oval access panel in the center. August 7, 2013 Followup from the Pelican Staff: Thanks for the additional information. Release screw. -Unclip clips and remove side trim inwards and upwards. -Lever out trim panel clips on inner window cavity cover strip. -Carefully lever out window cavity cover strip with MINI her latest blog December 18, 2014 Followup from the Pelican Staff: If the regulator is faulty, cutting the cable will release it. - Nick at Pelican Parts mongoman7071 Comments: Just like the
Thanks Clarke!! Mini Cooper Window Stuck Up It took me a few tries to get it positioned exactly where I could remove the pegs without trouble (See Figure 17).With the pegs removed, remove the window glass from the Sorry I cannot be more specific. Hook the two clips in and press the tabs into the frame.
Make sure that it goes up and down easily with no noise or binding. Close the doors and measure the depth that the window travels into the top and front edge of the door seal once the door is fully closed. Mini Cooper Window Reset Plastic pins just clip back into place. 9. Mini Cooper Window Wont Go Up Posting Quick Reply - Please WaitPosting Quick Reply - Please Wait « Previous Thread | Next Thread Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) Thread
BMW wouldn't sell me one but you can remove them by using your 5mm or 3/16" allen wrench. Check This Out I checked to make sure the door was completely closed, it was. November 12, 2015 Followup from the Pelican Staff: Glass can be scratched with metal, sand, or sometimes the wrong ice scraper. - Nick at Pelican Parts Mike Comments: These trip to sick bay; I hope they've changed the design of the motor this time around, but from the tone of the discussion here I fear that won't be the case. Mini Cooper Window Not Closing Properly
I have replaced both window regulators this year, with your help. Finally, if one of the barbed pins that secure the plastic cable retaining clips to the door frame snaps off, liquid nails makes for a quick, easy and effective fix. If these break you will have to figure something out. Source Now, take the supplied T20 Torx screws and tighten the upper frame and motor onto the gearbox.
We hope this blog will help to facilitate a good relationship with your auto shop, whether it's British American Auto Care or any other shop. Mini Cooper Window Replacement Angie I had the driver's side window motor replaced about three weeks ago on my '03 MC. Compare with the other door.
Pry the panel off with the pry tool. If the three bits get apart, it is kind of fussy to put the brushes back onto the commutator shaft. Once this gap is correct, tighten the two lower mounting bolts (See Figure 39).The last adjustment is the position adjustment. Mini R53 Window Not Working Transcript The interactive transcript could not be loaded.
Step 25: Secure the motor to the door with (3) phillip head screws. I've had body shop people tell me they've seen this phenomenon in several other Minis-has anyone else had this experience??? This will be 2 visits per window now. have a peek here Step 2: Now remove the door panel by removing (4) #30 torx screws in the door.
Large Image | Extra-Large Image Figure 13 This picture shows the two star shaped retaining pegs that secure the window glass to the window regulator (green arrows). These things should not be happening on a car thats this much "better" than the Cavalier in reliability. AM I PULLING THE PLUG FOR THE WIRE LEADING TO THE MOTOR? there is one thing that may be worth pointing out [and that you may not be aware of] and that is, if the window motor dies when the window is in
I also cannot hear the clicking sound when I press the toggle so it is time to replace the motor. Permalink I haven't had a MINI for over a year now so my recollections are rapid fading. They told me to take it to a dealer to see what the problem is and they'd see what they could do.